Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Blanco Home Additions & ADU: The Fort Worth Owner’s Guide
A Blanco home addition or ADU in Fort Worth typically runs $45,000 – $130,000 installed, depending on square footage, foundation work, and whether you’re adding a bathroom or kitchen to the new space. We stock the common Blanco-compatible hardware and finish parts on the truck, so most component failures don’t stall your project. The way owners usually find us: a Blanco sink or faucet that was fine last week suddenly leaks, drips, or the finish is flaking, and the original install left no paperwork behind.
Key Takeaways
- Blanco components rarely need full replacement – most failures are seals, cartridges, and mounting hardware, not the sink body or main fixture.
- Installed part replacement in Fort Worth runs $150 – $600 for faucet cartridges and sink mounting work, well under the cost of ripping anything out.
- We’re an independent Fort Worth contractor – not affiliated with Blanco, but we install and service their full residential line.
- Luca Romano personally walks every project before we order parts, so the first fix is the right fix.
Which Blanco Models This Applies To
Blanco’s North American lineup breaks into a few families we see constantly in Fort Worth remodels: the SILGRANIT composite sinks (diamond-shaped drain grooves, color codes like Anthracite, Truffle, and Metallic Gray), the stainless steel DURINOX and IKON series, and the faucet lines – Culina, Linus, and Torano. Each family has its own mounting pattern, drain size, and cartridge spec. The SILGRANIT sinks use a standard 3.5-inch drain opening, but the basket strainer has a Blanco-specific collar that seals differently than a big-box universal. If someone swapped in an off-the-shelf strainer, that’s usually the source of a slow leak.
For faucets, the culina line uses a 35mm ceramic disc cartridge. The Linus uses a different stem entirely. You identify the right part by popping the handle and reading the cartridge number stamped on the side, not by the model name alone. OEM Blanco cartridges run $40 – $80 and are worth it for faucets under warranty or heavily used. For out-of-warranty faucets in rental ADUs, a quality aftermarket cartridge with the same 35mm spec does fine and typically saves about 30%.
Styles & brands we work with
Signs Your Blanco Home Addition or ADU Component Is Failing
- Dripping from the spout hours after shutoff. The ceramic discs in the cartridge have worn or cracked. This is the most common call we get, and it’s always a cartridge swap – the faucet body itself is fine.
- Water staining the cabinet floor under the sink. Nine times out of ten, it’s the strainer collar seal under the SILGRANIT basket, not a pipe. The rubber dries out in North Texas heat and loses its compression.
- Cloudy finish on a stainless sink that won’t polish out. Fort Worth’s hard water plus mineral deposits eat through the clearcoat on DURINOX sinks. Once the finish goes, pitting follows within a year if it isn’t sealed.
- Faucet base wiggling or pulling up. The mounting nut backed off, usually because the original installer didn’t torque it against the deck plate. Left alone, the supply lines flex every time you use the handle and fatigue at the connection.
- Low flow that gets worse over months. Mineral scale inside the aerator is half the story. The other half is that the cartridge’s inlet ports are clogged with the same scale. Soaking is temporary; a $50 cartridge replacement is the real fix.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included
Blanco component replacement in Fort Worth is a fixed-price job, not an open-ended repair call. A faucet cartridge swap runs $150 – $300 installed, including the OEM part. A strainer seal and collar replacement on a SILGRANIT sink is $200 – $400 depending on access. Full faucet replacement with a new Blanco unit lands at $400 – $900 with labor, disposal of the old unit, and a written line-item quote before we start. These are parts-and-labor numbers, not “parts only, you figure out the install.”
Every component repair carries our 365-Day Done Right Promise. If the same part fails within a year of our fix, the second visit is free and we cover the replacement part. That’s in writing on the invoice, not a verbal handshake.
DIY or Call Us?
You can safely check three things before calling: whether the shutoff valves under the sink actually turn, whether the drip stops completely when handles are fully off, and whether the mounting nut under the faucet is loose. That last one you can hand-tighten. Beyond that, Blanco faucets and SILGRANIT sinks are not plumbing-friendly to a first-timer. The cartridges seat under spring tension, and over-torquing the retaining collar cracks the faucet body, which turns a $50 part into a $400 faucet. The strainer collar on SILGRANIT needs a specific compression sequence or it leaks worse than before you touched it. If you’re not sure, call (682) 841-6652 and we’ll talk you through whether it’s worth a visit. Most calls don’t need one.
FAQs
Twenty years or more with basic care. The failure point in Fort Worth is the strainer seal and mounting collar, not the sink itself. Plan on re-sealing every 5 – 7 years in our climate, and the sink body will outlast every faucet you pair with it. Call (682) 841-6652 if yours is weeping – a re-seal is a two-hour fix.
Yes, in most cases. If the drip is from the spout, it’s the cartridge, and a $50 – $80 OEM cartridge brings it back to new. If water is coming from the base, it’s a seal or the mounting nut. Replacement only makes sense when the finish is failing or the body is cracked, which is rare. We quote both options before you commit to either.
Most cartridge and seal replacements are done in under two hours. Full faucet swaps run three to four hours including old-unit removal and supply line inspection. The work talks. We just back it up.
We carry common Blanco cartridges, strainers, and mounting hardware for the Culina, Linus, and SILGRANIT lines, plus compatible aftermarket equivalents for out-of-warranty fixtures. If your part isn’t on the truck, we order OEM same day and it’s usually in hand within 48 hours. When we’re on a larger home addition or ADU build in Fort Worth, we also stock parts for KraftMaid, Cambria, and Silestone finishes so one trade doesn’t stall the whole schedule.
If you’re in Fort Worth and a Blanco component is leaking, loose, or just not right, call (682) 841-6652. We’ll get you a written price before any work starts and you’ll know exactly who is walking in your door.
Written by Luca Romano, Owner & Lead Remodeler, Sawyer Remodel Fort Worth at Sawyer Remodel Fort Worth, serving Fort Worth and nearby areas.
