Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
ES Windows Roofing: The Fort Worth Owner’s Guide
We stock and install ES Windows-compatible roofing parts across Fort Worth, with most replacements running $400 to $1,800 installed depending on the specific component and roof configuration. Homeowners usually discover a failure the same way: a leak shows up on the ceiling after a storm, or a window unit suddenly feels loose in its frame during a windy afternoon. The good news is that ES Windows roofing components are standardized enough that we can typically identify the right part, match it to your model, and complete the swap in a single visit.
ES Windows are built differently than standard residential windows. The roofing integration points, flashing channels, and mounting flanges are sized to ES Windows’ factory specifications, not generic off-the-shelf dimensions. When a roofer grabs whatever flashing is on the truck, you get gaps that fail inside of two seasons. In Fort Worth, with our hail seasons and July sun baking roof surfaces to 150-plus degrees, a mismatched part fails fast. The work talks. We just back it up.
As an independent service provider, Sawyer Remodel Fort Worth is not affiliated with ES Windows. We simply know the product line well enough to fix it right the first time, and we put the price in writing before we start.
Which ES Windows Models This Applies To
ES Windows produces several residential lines, and the roofing-related components vary by series. The compatibility question starts with reading the label. Look for a small etched or printed sticker on the window frame or sash, typically in the corner. The label carries the series code, manufacture date, and glass specs. If the label is faded or painted over, we measure the frame and identify the series by its profile dimensions during the estimate visit.
The main ES Windows lines you’ll find in Fort Worth homes are the aluminum frame residential series, which uses a specific flashing leg height and screw boss spacing. The older ES Windows units installed in 1990s-era neighborhoods like Wedgwood or Meadowbrook have different fastener spacing than the current production models. That is the single biggest compatibility gotcha: the mounting holes do not line up across generations. We carry adapters and drill-free flange converters to bridge the older units, but any contractor quoting the job without checking fastener spacing is guessing.
For the part itself, the choice is OEM or quality aftermarket. ES Windows OEM parts are not always easy to source quickly, and pricing can be unreasonable for small components. Good aftermarket equivalents from manufacturers like GAF or CertainTeed typically meet or exceed the original spec, especially for flashing and sealant systems. We stock both and recommend based on the part that failed, not a blanket brand loyalty.
Styles & brands we work with
Signs Your ES Windows Roofing Is Failing
- Water staining around window returns at the roofline. This usually means the flashing channel has separated from the window frame. Fort Worth’s freeze-thaw cycles work the sealant loose over two to three winters, and water finds the gap.
- Loose window unit that rattles in high wind. The roofing-side mounting flange has backed off its fasteners. Homes near Ridglea Hills or along the open exposure west of Loop 820 get hit harder by wind, and the stress concentrates exactly at that flange.
- Visible gaps between the roofing material and the window frame. The kickout flashing or counter-flashing has shifted. This is a straightforward fix when caught early, and a full roof-deck repair when ignored for a season.
- Granules from shingles piling up in the window track or on the sill below a roof-window intersection. The shingle edge at the window transition is failing, which means the underlying sealant underneath is likely already compromised.
- Condensation or fogging inside the glass unit itself. That is a failed seal in the insulated glass, not a roofing part. But if the window sits under a roofing overhang where flashing failed, we replace the glazing assembly at the same time and fix the root cause once.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included
Installed pricing for ES Windows roofing parts in Fort Worth runs from $400 to $1,800, and the range is driven by a few honest factors. A simple flashing replacement on a single-story roof-accessible window is on the low end. A full removal and reset of a large fixed window with new fasteners, sealant, and trim work pushes toward the top.
Here is the breakdown before we touch a tool:
| Service | Typical Installed Range |
|---|---|
| ES Windows flashing replacement | $400 – $800 |
| Roof-to-window sealant & counter-flashing rebuild | $500 – $1,200 |
| Window removal, reset, and reflash | $700 – $1,800 |
| Full roof-window transition repair (both sides) | $900 – $1,800 |
Every quote includes the part, labor, sealant rated for Texas heat, and haul-away of anything we remove. The number we give you in writing is the number you pay. If we find hidden damage once the window is out, we stop and send you photos before adding anything to the scope. No change orders slid into the invoice at the end. That is the Relay Visibility Guarantee, and it applies to every job, including a single flashing swap.
Warranty on the work is covered by the 365-Day Done Right Promise. If the repair fails within a year, we come back and make it right. Written, signed, no argument.
DIY or Call Us?
There are things you can safely check. Visual inspection from the inside: water stains, daylight showing through gaps around the window frame, loose fasteners you can see. You can also clear debris that piles up at window-to-roof intersections, which matters in Fort Worth because oak leaves and hail debris trap moisture against the flashing.
What you should not do is get on the roof and start pulling flashing or lifting shingles. Roofing work around a window involves working at height, on a slope, often during a window of dry weather you do not want to waste. A reflashing done wrong simply moves the leak six inches and guarantees you pay twice. If the window unit itself is loose, the fastening system needs to be evaluated, not tightened blindly. Call us at (682) 841-6652 and we will give you a written price before any work starts. You will know who is coming, when they arrive, and what it costs.
FAQs
Flashing and sealant at the window-roof intersection typically last 10 to 15 years in North Texas, but our hail seasons and the intense summer heat can shorten that to 8 years on west-facing exposures. The fasteners themselves rarely fail; it is almost always the sealant and flashing that give out first. Call (682) 841-6652 for an inspection if your units are past year 10.
Sometimes, yes. If the flashing is intact and just the sealant has cracked, we can remove the old sealant, clean the channel, and reapply a Texas-rated sealant for a lower cost. But if the metal flashing itself is bent, corroded, or pulled away from the frame, a patch job will fail within a season and you will pay twice. We will tell you which situation you have, honestly, during the estimate.
A straightforward flashing replacement on one window is usually a half-day job. A full removal and reset with reflashing is a full day, sometimes into a second morning if we find deck damage underneath. You will get a photo update before and after, so you are not wondering what is happening up there. Call (682) 841-6652 and we will give you a timeline with the quote.
We stock common ES Windows flashing profiles, fasteners, and sealants on the truck, and we stock parts for the other brands we work with too: KraftMaid, Cambria, and Silestone. Oddball pieces or older-generation flanges may need a day or two to source, and we will tell you that up front rather than showing up empty-handed.
Written by Luca Romano, Owner & Lead Remodeler, Sawyer Remodel Fort Worth at Sawyer Remodel Fort Worth, serving Fort Worth and nearby areas.
