Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Schluter Driveway & Pavers: The Fort Worth Owner’s Guide
Schluter driveway and paver systems in Fort Worth typically run $7,000 to $18,000 installed for a full paver driveway, while smaller paver patio work lands between $3,500 and $11,000. We stock Schluter-compatible edge restraints, drainage profiles, and transition strips on our trucks, and most part-swap visits are completed in one trip.
Most Fort Worth homeowners discover they have a failing Schluter component the hard way: a paver starts sinking after a heavy rain, an edge restraint pops loose near the curb, or a drainage channel stops moving water and the driveway puddles for days. The part itself is rarely the whole story. It’s usually the prep underneath, the freeze-thaw cycle working on North Texas clay, or a transition detail that was never sealed the way it should have been. We identify the failed part, match it to your Schluter profile, and replace it so the system drains and holds the way it was designed to.
Which Schluter Models This Applies To
Schluter manufactures a range of exterior profiles and drainage channels that integrate with paver and driveway systems: the Schluter-BARA edge profiles, Schluter-KERDI-DRAIN channels, Schluter-TROBA drainage mats, and the Schluter-DITRA uncoupling membranes used under tiled driveway accents. The compatibility gotcha most owners miss is profile height. A BARA-RT edge restraint sized for a 1¼-inch paver won’t anchor a 2-inch paver without a riser, and if the profile sits proud of the surface, tires catch the lip and tear it loose within a season.
To identify your part, look for the Schluter profile code stamped on the underside or inside the channel body. If the stamp is worn off, measure the profile height in millimeters and the channel width across the top. OEM Schluter profiles are worth the cost for anything that carries vehicle weight. Aftermarket edge restraints are fine for walkway borders and patio perimeters, but the aluminum alloy spec on OEM Schluter profiles holds up better against Fort Worth’s clay soil movement. Our trucks carry the most common BARA heights, several drainage channel widths, and transition strips used where paver driveways meet concrete aprons or garage slabs.
Styles & brands we work with
Signs Your Schluter Driveway & Pavers Is Failing
- Pavers sinking along the edge of the driveway. The edge restraint has lost its anchor, usually because the spike pulled free of expanding clay soil. Once the border drops, the field pavers follow.
- A metal edge strip is bent, lifted, or visible above the paver surface. The profile took a hit from a tire, a trailer, or a mower. A lifted edge is a trip hazard and a liability.
- Water pooling in the middle of the driveway or at the garage door. The drainage channel is clogged with North Texas silt, or the channel body has separated from the surrounding paver bed. Water backs up instead of flowing through.
- Gaps opening between the paver edge and your concrete driveway or walkway. The transition profile between dissimilar materials has shifted. Clay soil swells and shrinks with rainfall, and the gap widens each cycle.
- Efflorescence or mineral staining on the edge profile. Water is wicking through the joint and leaving salt deposits. It’s an early warning that the drainage path is failing before the paver base erodes.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included
For a full Schluter-compatible paver driveway installation in Fort Worth, expect $7,000 to $18,000 depending on square footage, paver thickness, and how much base prep the existing grade requires. A paver patio runs $3,500 to $11,000. If you’re replacing just a failed Schluter part, like a single edge profile run or one drainage channel section, you’re looking at a much smaller ticket: typically $300 to $900 for the part plus labor, depending on length and whether the surrounding pavers need to be pulled and re-bedded.
| Scope | Fort Worth Price Range |
|---|---|
| Full paver driveway installation | $7,000 – $18,000 |
| Paver patio installation | $3,500 – $11,000 |
| Single Schluter edge profile replacement | $300 – $900 |
| Drainage channel section replacement | $300 – $900 |
Every quote is written before work starts. The price on your invoice is the price you approved, with no change orders unless you ask for something different mid-job. Our 365-Day Done Right Promise covers parts and labor for a full year. If a replaced profile fails inside that window, we come back on our dime.
DIY or Call Us?
You can safely inspect the damage yourself. Walk the edge, look for lifted profiles, and check whether the drainage channel is clogged. Pulling a bent edge strip and hammering in a new one sounds simple, but here’s where it goes wrong: if the base under the pavers has eroded, the new profile has nothing to anchor into. You’ll sink it in the clay, the pavers will shift in the next rain, and you’ll buy the part twice. If any part of the profile carries vehicle weight, or if pavers have already begun to settle, that’s a prep-and-fix job, not a part swap.
Luca Romano’s rule applies here: the work talks. We just back it up. If you’re unsure, call (682) 841-6652 and one of our techs will walk you through what we’re seeing before we ever schedule the truck.
FAQs
An OEM Schluter aluminum edge profile on a properly prepped base will last 15 to 25 years in Fort Worth’s climate, but the anchor spikes often need re-setting every 5 to 7 years because North Texas clay expands and contracts with moisture. Call (682) 841-6652 if you’re seeing movement at the edge.
Minor bends can sometimes be straightened and re-anchored if the profile is still structurally sound, but any profile that has pulled free of its base or cracked at the anchor points should be replaced outright. A straightened profile that re-bends under tire load fails again within months.
A single drainage channel section replacement typically takes 2 to 4 hours on site, including pulling the surrounding pavers, re-bedding the base, and re-installing everything to grade. We schedule a live arrival time so you’re not waiting on a four-hour window.
We carry the most common Schluter BARA edge profile heights, multiple drainage channel widths, and transition strips for paver-to-concrete junctions on our service trucks. If your part is an unusual size, we order it and return within the week.
Written by Luca Romano, Owner & Lead Remodeler, Sawyer Remodel Fort Worth at Sawyer Remodel Fort Worth, serving Fort Worth and nearby areas.
Need a Schluter part matched, priced, and installed right? Call (682) 841-6652 for a free estimate. Sawyer Remodel Fort Worth is an independent service provider, not affiliated with Schluter, and we also stock parts for KraftMaid, Cambria, and Silestone.
